ZY8160 60A DC-DC Intelligent POL
8V to 14V Input ? 0.5V to 2.75V Output
Data Sheet
8. Programmable Features
Performance parameters of ZY8160 POL converters
can be programmed via the industry standard I 2 C
communication bus without replacing any
components or rewiring PCB traces. Each
parameter has a default value stored in the volatile
memory registers detailed in Table 1. The setup
registers 00h through 14h are programmed at the
system power-up. When the user programs new
performance parameters, the values in the registers
are overwritten. Upon removal of the input voltage,
the default values are restored.
Table 1. ZY8160 Memory Registers
ZY8160 converters can be programmed using the
Graphical User Interface or directly via the I 2 C bus by
using high and low level commands as described in
the ‘”DPM Programming Manual”.
ZY8160 parameters can be reprogrammed at any
time during the system operation and service except
for the digital filter coefficients, the switching
frequency and the duty cycle limit, that can only be
changed when the POL output is turned off.
8.1 Output Voltage
The output voltage can be programmed in the GUI
Output Configuration window shown in the Figure 17
or directly via the I 2 C bus by writing into the VOS
Register
PC1
PC2
PC3
DON
DOF
TC
INT
Content
Protection Configuration 1
Protection Configuration 2
Protection Configuration 3
Turn-On Delay
Turn-Off Delay
Tracking Configuration
Interleave Configuration and
Address
00h
01h
02h
05h
06h
03h
04h
register shown in Figure 18.
Frequency Selection
RUN
ST
VOS
CLS
DCL
B1
B2
B3
C0L
C0H
RUN Register
Status Register
Output Voltage Setpoint
Current Limit Setpoint
Duty Cycle Limit
Dig Controller Denominator z -1
Coefficient
Dig Controller Denominator z -2
Coefficient
Dig Controller Denominator z -3
Coefficient
Dig Controller Numerator z 0
Coefficient, Low Byte
Dig Controller Numerator z 0
15h
16h
07h
08h
09h
0Ah
0Bh
0Ch
0Dh
0Eh
C1L
Coefficient, High Byte
Dig Controller Numerator z -1
0Fh
Figure 17. Output Configuration Window
C1H
Coefficient, Low Byte
Dig Controller Numerator z -1
10h
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
C2L
C2H
C3L
C3H
Coefficient, High Byte
Dig Controller Numerator z -2
Coefficient, Low Byte
Dig Controller Numerator z -2
Coefficient, High Byte
Dig Controller Numerator z -3
Coefficient, High Byte
Dig Controller Numerator z -3
Coefficient, Low Byte
11h
12h
13h
14h
VOS7 VOS6 VOS5 VOS4
Bit 7
Bit 7:0 VOS[7:0] , Output voltage setting
00h: corresponds to 0.5000V
01h: corresponds to 0.5125V
77h: corresponds to 1.9875V
78h: corresponds to 2.0000V
79h: corresponds to 2.025V
VOS3
VOS2 VOS1 VOS0
Bit 0
R = Readable bit
W = Writable bit
U = Unimplemented bit,
read as ‘0’
- n = Value at POR reset
VOM
Output Voltage Monitoring
17h
IOM
TMP
Output Current Monitoring
Temperature Monitoring
18h
19h
96h: corresponds to 2.750V
Figure 18. Output Voltage Setpoint Register VOS
ZD-01674 Rev. 1.2, 02-Jul-10
www.power-one.com
Page 14 of 30
相关PDF资料
0006660012 CABLE 28AWG 148MM RED
0006660013 CABLE 28AWG 300MM RED
002679-000 CABLE 22AWG TWISTED
0082226102 RIB CBL .100 100RL TIN 2POS
0082226104 RIB CBL .100 100RL TIN 4POS
0082226115 RIB CBL .100 100RL TIN 15POS
0192520124 TIE 4 INCH 18LB NATURAL
0192520125 TIE 6.1 INCH 18LB NATURAL
相关代理商/技术参数
ZY8160G-Q1 制造商:Power-One 功能描述:
ZY8160G-R1 功能描述:DC/DC转换器 8-14Vin 60A(max) 0.5-2.75Vout 29mA RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压(标称): 输出端数量:1 输出电压(通道 1):3.3 V 输出电流(通道 1):600 mA 输出电压(通道 2): 输出电流(通道 2): 安装风格:SMD/SMT 封装 / 箱体尺寸:
ZY82 制造商:FAGOR 功能描述:FAGOR S9G7A 制造商:General Instruments 功能描述:Zener Diode, Two Terminal, 82 Volt, 6.7%, DO-15
ZY82B 制造商:DIOTEC 制造商全称:Diotec Semiconductor 功能描述:Silicon Power Z-Diodes (non-planar technology)
ZY82GP 制造商:未知厂家 制造商全称:未知厂家 功能描述:2 W Glass Passivated Zener Diode
ZY8V2GP 制造商:未知厂家 制造商全称:未知厂家 功能描述:2 W Glass Passivated Zener Diode
ZY9.1 制造商:DIOTEC 制造商全称:Diotec Semiconductor 功能描述:Silicon-Power-Zener Diodes (non-planar technology)
ZY9.1V 制造商:CDIL 制造商全称:Continental Device India Limited 功能描述:SILICON GLASS PASSIVATED 2.0 WATT ZENER DIODES